Remington shank mods!
-
- Posts: 434
- Joined: Thu Aug 16, 2018 12:59 pm
Remington shank mods!
Anyone shaved the shank on a Remington for deeper fit in a Morse tapered receiver?.. If so, what was the resulting blow?... (Given that the end of shank goes furter in against the venturi)
Thanks!
Trond
Thanks!
Trond
-
- Posts: 256
- Joined: Thu Oct 25, 2018 5:11 am
- Location: Somerset, UK
Re: Remington shank mods!
I used to have a Remington which had had the shank modified to fit a standard large bore Morse taper receiver. I did a comparison with it in my Gen II 88H and an original Remington in a friends Elkie 88H. I could not detect any difference in the way they blew. I also have a Connstellation Remington with the small shank which I use in a 74H and that works in a very similar way but has an improved upper register as you would expect.
Cheers
Stewbones43
Cheers
Stewbones43
Conn 36H(Pitched in D/A)
Reynolds Medalist
B&H Sessionair
Besson 10-10
Conn 74H
Yamaha YSL-641 with Yamaha Custom Slide
Conn 88H Gen II with Conn SL4747 Slide
Besson Academy 409
Rath/Holton/Benge Bb/F/G or Gb/Eb or D Independent Bass
Reynolds Medalist
B&H Sessionair
Besson 10-10
Conn 74H
Yamaha YSL-641 with Yamaha Custom Slide
Conn 88H Gen II with Conn SL4747 Slide
Besson Academy 409
Rath/Holton/Benge Bb/F/G or Gb/Eb or D Independent Bass
-
- Posts: 434
- Joined: Thu Aug 16, 2018 12:59 pm
Re: Remington shank mods!
Thanks!stewbones43 wrote: ↑Tue May 11, 2021 6:47 am I used to have a Remington which had had the shank modified to fit a standard large bore Morse taper receiver. I did a comparison with it in my Gen II 88H and an original Remington in a friends Elkie 88H. I could not detect any difference in the way they blew. I also have a Connstellation Remington with the small shank which I use in a 74H and that works in a very similar way but has an improved upper register as you would expect.
Cheers
Stewbones43
I am thinking about ordering a 1919 Conn replica Leadpipe from Brassark and they can deliver it with Remington receiver without extra charge.. However, as i am still undecided as to which mouthpiece to use i am thinking standard Morse...
- ithinknot
- Posts: 1112
- Joined: Fri Jul 24, 2020 3:40 pm
Re: Remington shank mods!
Perhaps have Bob Reeves cut the mouthpiece for sleeves, so that you can use it as either Remington or Morse?
-
- Posts: 76
- Joined: Wed Aug 08, 2018 9:41 am
Re: Remington shank mods!
I had Robb Stewart in LA (now retired, I think) modify a couple of Remington pieces to fit a stock Bach 42 leadpipe. He did it in about 5 mins total, threw it in his lathe and BAM! Robb is a brass tech wizard (really!), but av good tech should be able to do it pretty easily.
-
- Posts: 434
- Joined: Thu Aug 16, 2018 12:59 pm
Re: Remington shank mods!
How did it blow afterwards?droffilcal wrote: ↑Fri May 14, 2021 10:56 pm I had Robb Stewart in LA (now retired, I think) modify a couple of Remington pieces to fit a stock Bach 42 leadpipe. He did it in about 5 mins total, threw it in his lathe and BAM! Robb is a brass tech wizard (really!), but av good tech should be able to do it pretty easily.
-
- Posts: 76
- Joined: Wed Aug 08, 2018 9:41 am
Re: Remington shank mods!
They worked great, better than before, but it wasn’t a revelation or anything like that; I would say that if you love the Remington already then you’ll probably be even happier with the modified shank, but it likely wouldn’t change your opinion in a substantial way.
Does that make sense?
Does that make sense?
-
- Posts: 434
- Joined: Thu Aug 16, 2018 12:59 pm
Re: Remington shank mods!
Yes, that makes sense... The reason i am a bit sceptical is that the the Leadpipe i plan to use is a 1919 Conn replica which have the venturi at a different spot than usual (I suspect closer to the end of the mouthpiece shank) and the gap between the end of the shank and the venturi will be too short.. (obviously because the piece will protrude furter into the receiver) Now, does that make sense?droffilcal wrote: ↑Sat May 15, 2021 11:41 am They worked great, better than before, but it wasn’t a revelation or anything like that; I would say that if you love the Remington already then you’ll probably be even happier with the modified shank, but it likely wouldn’t change your opinion in a substantial way.
Does that make sense?
-
- Posts: 20
- Joined: Fri Jul 06, 2018 7:34 am
- Location: Ohio
- Contact:
Re: Remington shank mods!
I found this trick on the Bob Reeves blog for trumpet mouthpieces that actually works for trombones as well. It helped me notice a difference on my Elkhart 62H with a Yeo mpc.
https://bobreeves.com/blog/this-one-sim ... et-easier/
https://bobreeves.com/blog/this-one-sim ... et-easier/
-
- Posts: 434
- Joined: Thu Aug 16, 2018 12:59 pm
Re: Remington shank mods!
Brilliant! Thanks will do!jeremyesmith wrote: ↑Sun May 16, 2021 6:00 am I found this trick on the Bob Reeves blog for trumpet mouthpieces that actually works for trombones as well. It helped me notice a difference on my Elkhart 62H with a Yeo mpc.
https://bobreeves.com/blog/this-one-sim ... et-easier/
( allthough trumpet have a more pronounced gap than trombone, this adresse the problem)