Hammond Mouthpiece Specs
-
- Posts: 30
- Joined: Wed Oct 05, 2022 4:55 pm
Hammond Mouthpiece Specs
Was considering trying a Hammond for my small bore and was curious on the difference between the S & M cups. Also, is the skeletonized bank worth considering vs the standard. I've only used more standard pieces, so I know little on more lightweight pieces.
- MalecHeermans
- Posts: 128
- Joined: Mon Apr 23, 2018 6:40 pm
- Location: Brooklyn
- Contact:
Re: Hammond Mouthpiece Specs
Of course this is all subjective, but the S cup felt too shallow for me. I also wasn't wild about the light blank.
-
- Posts: 30
- Joined: Wed Oct 05, 2022 4:55 pm
Re: Hammond Mouthpiece Specs
In what way did you find it too shallow?MalecHeermans wrote: ↑Thu Aug 17, 2023 1:45 pm Of course this is all subjective, but the S cup felt too shallow for me. I also wasn't wild about the light blank.
- dukesboneman
- Posts: 738
- Joined: Mon Apr 02, 2018 4:40 pm
- Location: Sarasota, Florida
- Contact:
Re: Hammond Mouthpiece Specs
FRom what I understand, Not alot of difference between S & M cups
I have a 6S and concidering getting a M cup
I agree The Light weight cup doesn`t work as well and I don`t like the look
I have a 6S and concidering getting a M cup
I agree The Light weight cup doesn`t work as well and I don`t like the look
-
- Posts: 116
- Joined: Fri Dec 11, 2020 6:53 am
Re: Hammond Mouthpiece Specs
S cup is shallower than M but has a U shape, and M has a V shape. For me, S is much more convenient than M. Your preferences may vary.
- Finetales
- Posts: 1093
- Joined: Fri Mar 23, 2018 12:31 pm
- Location: Los Angeles
- Contact:
Re: Hammond Mouthpiece Specs
I've actually never played a standard blank Hammond small shank piece, only the skeletonized blank (of which I've owned a couple). 13M is a really nice do-everything small piece, 11M is good for 3rd parts and the like.
- BrianJohnston
- Posts: 752
- Joined: Sat Jul 11, 2020 7:49 pm
- Location: North America
- Contact:
Re: Hammond Mouthpiece Specs
I have played a 12s which I liked. Never really had a use for the "M" cup, but I really like all of Karl Hammond's mouthpieces in both blanks, although I prefer the standard blank a tad more than the light blank.
Fort Wayne Philharmonic
Lima Symphony Orchestra
Lima Symphony Orchestra
- muschem
- Posts: 249
- Joined: Sun Jan 17, 2021 10:16 am
- Location: Austin, Texas
- Contact:
Re: Hammond Mouthpiece Specs
I have a set of Hammond pieces that I had threaded for my Doug Elliott XT rims by Bob Reeves shop. They started as 10-sized pieces, and my XTN102.5 rim was a pretty close match for most of them. A couple of the smaller pieces had to be adjusted slightly to match the rim. I have the ML and M in both large and small shank, but I most often use:
- Large shank, standard blank 10ML on .547
- Small shank 10M on .525
- 10S on .500 and .508
- 10XS on alto
- MalecHeermans
- Posts: 128
- Joined: Mon Apr 23, 2018 6:40 pm
- Location: Brooklyn
- Contact:
Re: Hammond Mouthpiece Specs
In the usual way. I've found over the years that, being asked to play in many different situations, I like to have one sort of middle ground mouthpiece for each horn so I can fine tune the sound myself. Then I have maybe a smaller sounding one and a bigger sounding one for the moments when I have to play something a little outside of my norms. The Hammond S, to me, is a specialist mouthpiece. Something you might use when playing alto trombone, or on a very small bore tenor. That sound never really spoke to me. I also just find it physically uncomfortable and, over the years, I've found that comfort trumps sound. Again this is all personal and part of a long long journey in playing, so you may have different tastes. Fine!Trombola2112 wrote: ↑Mon Aug 21, 2023 6:57 pmIn what way did you find it too shallow?MalecHeermans wrote: ↑Thu Aug 17, 2023 1:45 pm Of course this is all subjective, but the S cup felt too shallow for me. I also wasn't wild about the light blank.